Service History 249

We serviced a

MAYTAG WASHER

Model MVWB765FC3

Near Hampden, Massachusetts 01036

Jorden

Job Details: 03/07/2025

"Arrived and found error codes F7E9 (locked rotor) and F0E3 (overloaded) stored in system, cleared codes. Ran unit and all operated normally but heard a loud clacking noise that only happened during spin (no noise when spinning by hand) and increased in frequency by speed. Units drain system is working perfectly. Ordering ACU because it sounds as if the control is throttling power to clutch when it shouldnt be and clutch as contingency. ; rqstng P&A on 1 W11429620 (ACU) and 1 W10754448 (clutch)"

We serviced a

WHIRLPOOL WASHER TL

Model CAE2745FQ2

Near West Hartford, Connecticut 06119

Mike K.

Job Details: 03/07/2025

"Control board monitor led solid. Unit will not go into diagnostics, no response to input..cycled power and same. Verified 120vac at wall and at control. Lower unit inspection all looks good. Tested connectivity from cont 16-2, 16-3 to drain pump and is good, 15 ohms on drain pump, good., so doesnt lock to be stuck in a manual drain, just unresponsive. Will reorder control as unit was running after tech replaced it last visit. As this was just done, no additional charges. Part covered under 24 month part warranty, labor collected on previous repair.Office to contact to schedule return when parts come in.; ordrng 1 W11712987 (Control)"

We serviced a

MAYTAG WASHER TOP LOAD

Model MVWB865GW0

Near Waxhaw, North Carolina 28173

Jonathan J.

Job Details: 03/07/2025

"Complete squeaking during agitation cycle/squealing That smell smells like WD-40 coming from the machine I found odor is caused by bacteria growing in tub. As far as noise, I cannot duplicate noise and agitation or spin cycle no error codes in fault history other than. F2e1 no electrical issues found. no rotor, stater or clutch issues found either agitator is slightly loose as far as the appliances, no suspension issues as far as excessive bounce, adjusted suspension rods and lubricated."

We serviced a

KITCHENAID MICOWAVE

Model KMLS311HBS-1

Near West Hartford, Connecticut 06107

Mike K.

Job Details: 03/07/2025

"Replaced fan and fan motor. Unit did have to come down to do so, reinstalled and tested fine with cup of water, fan running smoothly and heated properly"

We serviced a

WHIRLPOOL WASHER FL

Model WFW6620HW2

Near West Hartford, Connecticut 06117

Mike K.

Job Details: 03/07/2025

"Unit has been having continued suds errors. Previous repairs: Pressure sensor/ hose replaced, drain pump replaced, compressor belt valves replaced, bellow drain holes cleared.Says per office ran 5 cycle with no soap and worked fine, first regular load after that fine, next load, got suds error. On arrival could see suds in bellow.Ran quick cycle and completed fine. And no more suds seen. Soap being used is Tide ultra concentrated.F5e4 only error in history, door not open between cycles. Ran diagnostic cycle and completed fine. Raised drain tube a little higher in stand pipe to reduce chance of siphoning.They only thing found was when recirculating the water would just hit the door, not spray into the basket. Found the nozzle and tube are restricted, could mostly clear the nozzle, but result is same ordering nozzle and tubing. Also ordered pump in case the pump was source of issue.; rqstng P&A on 1 W11318802 (Hose) and 1 W11316251 (Nozzle) and 1 W11318805 (Dosing) and 1 W11458345 (Pump assy)"

We serviced a

GE REFRIGERATOR TO

Model GIE18GSNDRSS

Near Springfield, Massachusetts 01109

Jorden

Job Details: 03/07/2025

"Arrived and found FZ evap fan not running, flicked it and it kicked on. Informed customer and they opted to hold off on any repair since fan is running. Sent estimate to customer."

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Charlotte, North Carolina 28273

Clinton

Job Details: 03/07/2025

Used truck stock harness. Unit did have a bad control but the harness shorted caused the failure I assume the harness was just barley split bc it it did drain before but to drain when I wiggled wire there was no visible signs of damage.unit is fully operational after repair ; used 1 W11643701 (HARNESS LOWER) from stock

We serviced a

WHIRLPOOL WASHER TL

Model MVWC565FW2

Near Bloomfield, Connecticut 06002

Mike K.

Job Details: 03/07/2025

"Unit not starting running on its own. Unplugged on arrival, plugged in and unit is in manual drain. Allowed to finish. F8e1 only error in history. Ran diagnostic cycle. Completed fine, recalibrated and cs to monitor."

We serviced a

WHIRLPOOL DRYER

Model WED5010LW1

Near Charlotte, North Carolina 28227

Johnny

Job Details: 03/06/2025

"Cx stated unit drying. Couldnt not confirm complaint. Unit heats and cycles as designed. Cx stated unit no longer catching lint, I observed lint and water built up in dryer vent hose confirming there is an airflow issue. Instructed cx to have vent cleaned professionally. Unit working as designed."

We serviced a

WHIRLPOOL DRYER

Model WET4024HW0

Near Sturbridge, Massachusetts 01518

Chris B.

Job Details: 03/06/2025

Complaint that the dryer is leaving marks on the clothes. Found dryer over heating and clothes getting stuck on the steel grill exhaust on the inside and marking the clothes. Mentioned to the customer to clean the lint screen after every use and to periodically clean the venting to the outside of the home. Dryer working normal.

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS3

Near Scituate, Rhode Island 02857

Lee

Job Details: 03/06/2025

"Customer states new issue on arrival, found a black gasket sitting bottom of tub end of cycle, confirmed issue, found it was the gasket the is supposed to be around diverter disc but has stretched out too much to fit now, replaced off truck with new wash motor, replaced control, ran diagnostics cycle, confirmed unit is working properly.; used 1 W11416362 (MOTOR/SUMP) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR FDB

Model WRF555SDFZ11

Near Plainville, Connecticut 06062

Andre

Job Details: 03/06/2025

"Ck unit upon arrival and found water spraying from the top of refrigerator coming from fill tube to ice maker order tube for replacement, also inform customer more rust is not covered. Customer insisted inform customer if warranty inform him that door would need to be replace his warranty would need to provide a specific Authorization for the replacement of all 3 door. As for my knowledge rust is not covered ; ordrng 1 W11415785 (Fill tube)"

We serviced a

WHIRLPOOL WASHER TL

Model WTW2000HW0

Near Chicopee, Massachusetts 01020

Jorden

Job Details: 03/06/2025

"Arrived and found complaint: tub is loose. Ran unit and confirmed proper operation, nothing out of the ordinary. Informed customer how the tub is suspended by damper rods unlike the old style units where it sat on a pedestal. Unit tests fine. Informed customer should we return and find no manufacturing defect then customer would be responsible for service fee."

We serviced a

KITCHENAID RANGE

Model KSDG950ESS1

Near Springfield, Massachusetts 01107

Jorden

Job Details: 03/06/2025

"Arrived and found bake element broken/open, replaced and tested fine. ; used 1 W10779716 (ELEMENT) from stock"

We serviced a

MAYTAG WASHER

Model MVW7230HW0

Near Springfield, Massachusetts 01108

Jorden

Job Details: 03/06/2025

"Arrived and installed spin basket, agitator, bolt and spanner nut, tested fine."

We serviced a

WHIRLPOOL REFRIGERATOR FDB

Model WRF560SEYM00

Near Springfield, Massachusetts 01108

Jorden

Job Details: 03/06/2025

"Arrived and found both rooms near room temp, no frost pattern and compressor drawing .4amps. Unit needs sealed system repair. Be certain to leak/pressure check before charging. Document with tech support after repair is complete findings of the leak check and current status of unit when you leave. ; rqstng P&A on 1 WPW10466675 (compressor) and 1 123789 (2nd time slot), states that autho needed"

We serviced a

KITCHENAID RANGE

Model KSEG700ESS6

Near Ellington, Connecticut 06029

Gary V.

Job Details: 03/06/2025

"Installed bake element, Ui panel and door seal. Cycled and tested fine."

We serviced a

WHIRLPOOL WASHER FRONT LO

Model WFW560CHW4

Near Charlotte, North Carolina 28208

Clinton

Job Details: 03/06/2025

Installed harness for broken wire unit is now washing and door is locking

We serviced a

WHIRLPOOL RANGE

Model WFE535S0LS3

Near Charlotte, North Carolina 28214

Clinton

Job Details: 03/06/2025

Unit is covered in roaches void warranty can not service

We serviced a

WHIRLPOOL WASHER TL

Model WTW6157PW0

Near Charlotte, North Carolina 28214

Clinton

Job Details: 03/06/2025

Hot and cold valve reversed u it had long fill error speared error leveled leg on unit as well free adjustments unit functions all are work as designed

We serviced a

MAYTAG WASHER TL

Model MVWX655DW1

Near Fort Mill, South Carolina 29715

Caleb

Job Details: 03/06/2025

"Gearcase leaking oil on cam and belt, preventing belt from spinning, unit will need a new Gearcase belt and cam, customer to decide on repairs at this time."

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF606ESS01

Near North Providence, Rhode Island 02904

Lee

Job Details: 03/06/2025

"Installed fan, tested properly"

We serviced a

JENN-AIR RANGE

Model JES1750ML1

Near Providence, Rhode Island 02906

Lee

Job Details: 03/06/2025

"Customer states unit makes a lot of noise when using the down draftExplained to customer noise is normal operation it is airflow, took video and sent to techline, they confirmed it is within normal operation.7741087643"

We serviced a

GENERAL ELECTRIC REFRIGERATOR

Model PVD28BYNCFS

Near Kings Mountain, North Carolina 28086

Ryan S.

Job Details: 03/06/2025

Insrallled new fans in freezer . Ran unit unit not making noise and operating as designed .

We serviced a

WHIRLPOOL REFRIGERATOR FDB

Model WRX735SDHZ08

Near Gastonia, North Carolina 28056

Ryan S.

Job Details: 03/06/2025

"Customer complained unit not making ice. Found unit had ice in ice bin but auger not sending ice to door when prompt. Found auger motor coming on. Found yoke slipping . Ordering auger motor , yoke, washer and divider . Informed customer office will call when parts come in. ; ordrng 1 WPW10309864 (Ice box divider) and 1 W11671282 (Auger motor) and 1 WP63052-2 (Yoke) and 1 W11378860 (Washer)"

We serviced a

JENNAIR FREEZER

Model JBZFR30IGX10

Near Belmont, North Carolina 28012

Clinton

Job Details: 03/06/2025

Spoke with tech line advised there is new control software in limited supply and they will contact in the new few days with follow up with Randy on email. submitted in product review with Steve Kelly lead engineer will send control was told can not order and there is no part number Randy is contact Randycox.advantage@gmail.com also was advised to replace fill tube again with control 7741088027; ordrng 1 W11515313 (Fill tube)

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW3

Near Charlotte, North Carolina 28278

Clinton

Job Details: 03/06/2025

Installed new control ran unit is diagnostic after unit fully operational no errors or issues

We serviced a

WHIRLPOOL MW/WALL OVEN COM

Model WOC54EC0HS03

Near South Windsor, Connecticut 06074

Gary V.

Job Details: 03/06/2025

"Inspected and found f1e6 fault now indicating failed magnetron, also found debris from old mag may have fallen into wave giude causing cover to burn and new mag to short out, will submit estimate and call with return date, ordering inverter board again for back up.; rqstng P&A on 1 W11346197 (Magnetron) and 2 W10915651 (Wave guide cover)s and 1 W11325604 (Inverter board)"

We serviced a

KITCHENAID REFRIGERATOR

Model KSF26C4XYY03

Near South Windsor, Connecticut 06074

Gary V.

Job Details: 03/06/2025

"Inspected and found ice maker stuck mid cycled and broken , also found wire harness thru freezer door hinge point broken, needs freezer door and ice maker, will submit estimate and call.; rqstng P&A on 1 W10410951 (Stainless freezer door) and 1 WPW10251076 (Ice maker)"

We serviced a

WHIRLPOOL DISHWASHER

Model KDTM404KPS1

Near Windsor, Connecticut 06095

Gary V.

Job Details: 03/06/2025

"Inspected and found excess suds in sump and customer may have accidentally used wrong detergent, flushed suds out and cycled, tested fine."

We serviced a

WHIRLPOOL WASHER TL

Model WTW4816FW3

Near Windsor, Connecticut 06095

Gary V.

Job Details: 03/06/2025

Inspected and found pressure system fault for main control. Replaced with new control board and cycled thru diagnostics test and tested fine now.

We serviced a

WHIRLPOOL WASHER TL

Model WTW5057LW1

Near Windsor Locks, Connecticut 06096

Gary V.

Job Details: 03/06/2025

"Inspected and found water weeping paste inlet valve into tub, needs new inlet valve, will order and return. Customer wants next Thursday am slot.; ordrng 1 W11513255 (Inlet valve)"

We serviced a

MAYTAG WASHER

Model MVW7232HW2

Near Westfield, Massachusetts 01085

Mike K.

Job Details: 03/06/2025

Replaced lid and operating correctly

We serviced a

WHIRLPOOL DRYER

Model WED4950HW0

Near Agawam, Massachusetts 01030

Mike K.

Job Details: 03/06/2025

Replaced timer and testing fine

We serviced a

MAYTAG WASHER TOP LOAD

Model MVW7232HW1

Near Charlotte, North Carolina 28227

Johnny

Job Details: 03/06/2025

Installed new part. Ran calibration cycle. Ran service cycle. Started regular cycle till point of agitation. Unit working as designed.

We serviced a

MAYTAG WASHER

Model MVW6230HW2

Near Charlotte, North Carolina 28227

Johnny

Job Details: 03/06/2025

"Entered service mode and activated spin. Unit just hummed. Observed capacitor hanging down under unit. Replaced with new one. Ran calibration cycle. Unit wouldnt shift to agitate. Replaced actuator. Ran service cycle. Unit would not drain, but drain pump constantly hummed. Replaced drain pump. Ran calibration cycle, ran service cycle, unit only agitate in one direction. Ordering necessary parts for repair; rqstng P&A on 1 W11283592 (Motor) and 1 W11567712 (Control board) and 1 W11590868 (Harness), used 1 W11395618 (CAPACITOR/INTER COIL), 1 W11399437 (DRAIN PUMP), and 1 W10913953 (ACTUATOR) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ04

Near Sutton, Massachusetts 01590

Glenn

Job Details: 03/06/2025

Installed ice maker in freezer tested all ok

We serviced a

JENNAIR MW/WALL OVEN COM

Model JMW3430IL03

Near Charlotte, North Carolina 28277

Caleb

Job Details: 03/06/2025

"Microwave would not start and the ui had a partial display when operating the lower oven, customer stated that they did not try cycling the power, This area was hit with bad thunderstorms yesterday. After cycling the power the microwave started fine with no issues, and display was corrected. Unit tests fine at this time, confirmed with customer."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT710PAYM3

Near Charlotte, North Carolina 28277

Caleb

Job Details: 03/06/2025

"Confirmed broken rack, rollers broken and rail is slightly bent, stop clip broken as well, unit has 2 errors F1E1 stuck relay on control and confirmed heater is defective, took pic. Evidence of water leaking from seal. Sump will run in diagnostics but will not run out of diagnostics. When sump is running there is a pulsing sound that increases in sound and frequency the longer it runs, vibrates really bad. ; ordrng 1 W10518394 (Heater) and 2 WPW10350401 (Rollers)s and 1 WPW10195623 (Rail) and 1 WPW10195622 (Clip) and 1 W10479763 (Control) and 1 W10542314 (Seal)"

We serviced a

WHIRLPOOL REFRIGERATOR TM

Model WRT518SZFM04

Near Charlotte, North Carolina 28226

Caleb

Job Details: 03/06/2025

"Confirmed failed defrost sensor and fan motor, advised customer that unit will need to be unplugged 24-48 hrs before service. ; ordrng 1 W11609822 (Harness) and 1 WP2315539 (Fan motor)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT541SZDB03

Near Sutton, Massachusetts 01590

Glenn

Job Details: 03/06/2025

SR # 741086828 Found the freezer light switch is broken and the wires will not pull out of the insulation so we are unable to replace the switch tech line is sending it for review and likely replacement.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ2

Near Grafton, Massachusetts 01536

Glenn

Job Details: 03/06/2025

Installed part dishwasher no longer leaks from the door but drips under the door need lower seal and screws. ; ordrng 6 W11627527 (Screws)s and 1 W11664713 (Lower seal)

We serviced a

WHIRLPOOL RANGE

Model WFES3030RS0

Near Mount Holly, North Carolina 28120

Ryan S.

Job Details: 03/06/2025

"Installed new gasket, found frame holes dont line up on left two holes so used a bit of high temp glue on just those two holes, all other holes above and below are working properly. Using high temp glue will hold in bad spots . Verified proper operation."

We serviced a

MAYTAG WASHER TL

Model MVW4505MW1

Near Southington, Connecticut 06489

Andre

Job Details: 03/06/2025

Ck unit upon arrival and customer show me video of unit sounding like a train. Check cam kit with belt and found no no wear and tear customer did state that noise would started after the 2nd full wash. Gear case heating up. Quote customer for GearCase replacement and customer declined estimate for repair.

We serviced a

MAYTAG WASHER TOP LOAD

Model MVW7232HW2

Near Mint Hill, North Carolina 28227

Johnny

Job Details: 03/06/2025

"Drain pump constantly energized and lid would not unlock, user interface non responsive. Could not get picture of model and serial number. Will need new control board.; ordrng 1 W11687817 (Control board)"

We serviced a

WHIRLPOOL DRYER

Model WGD560LHW4

Near Cranston, Rhode Island 02910

Lee

Job Details: 03/06/2025

"Installed both parts, problem still occurs, ordering burner assembly ; ordrng 1 W11652258 (Burner assm.)"

We serviced a

WHIRLPOOL RANGE

Model WFG320M0MB0

Near Warwick, Rhode Island 02889

Lee

Job Details: 03/06/2025

"Customer states more cosmetic issue, burner head peeling, cooktop paint peeling, will order both parts, also was sent with wrong door liner. Need W10446851 door liner; ordrng 1 W10446851 (liner-door) and 2 W11435630 (Burner head)s and 1 W11435659 (Burner head) and 1 W11435657 (Burner head) and 1 W11590287 (Cooktop)"

We serviced a

SAMSUNG REFRIGERATOR FDB

Model RF23M8070SR/AA

Near Bristol, Rhode Island 02809

Lee

Job Details: 03/06/2025

"Installed compressor, tested okay; dspstn on spec-tagged invntry: 1 W11506635 COUPLER 6 NF MS SV PROCES"

We serviced a

JENNAIR DISHWASHER

Model JDPSS246LL1

Near Stanley, North Carolina 28164

Ryan S.

Job Details: 03/06/2025

Installed new sump motor ran unit to check for leaks . no leaks detected . verified proper operation

We serviced a

JENNAIR REFRIGERATOR FDB

Model JFFCF72DKL05

Near Stanley, North Carolina 28164

Ryan S.

Job Details: 03/06/2025

Install new hinge and mullion. door now closing properly . verified proper operation

We serviced a

WHIRLPOOL RANGE

Model KCGD500GSS05

Near Denver, North Carolina 28037

Ryan S.

Job Details: 03/06/2025

"Came to install parts ordered by previous tech. Installed switch harness, igniter and soark module. Verified unit lighting all the time now."

We serviced a

KITCHENAID REFRIGERATOR FDB

Model KRMF706ESS01

Near Huntersville, North Carolina 28078

Ryan S.

Job Details: 03/06/2025

"Arrived and found unit low to empty of refrigerant. Charged nitrogen and fiubd valve stem on filter drier bad. Replaced valve stem and charged again. Held steady for 10mins. Vaccines unit for 20min, steady for 5mins. Charges 6oz r134. Frost pattern formed immediately. Watched for 15min, frost pattern still present. Informed customer to give 24fot proper cool, 48hr for ice."

We serviced a

WHIRLPOOL RANGE

Model WSES7530RZ0

Near Dallas, North Carolina 28034

Ryan S.

Job Details: 03/06/2025

"Customer complained unit fan keeps running and cooktop light stays on. Also right rear element not working. Also had spark under console found pinched wire to infinite switches, ordering harnesses , ordering both right rear and right front infinite switches and right rear element also ordering ACU due to possible short. Informed customer office will call when parts come in. Will call safety after job complete on return call; ordrng 1 FSPW11747380 (Acu) and 1 W11747427 (Harness cooktop) and 1 W11747425 (Harness console) and 1 W11747426 (Harness DC) and 1 W11747449 (RR element) and 1 W10911303 (RR switch) and 1 W10437097 (RF switch)"

We serviced a

MAYTAG DRYER

Model MEDX655DW1

Near York, South Carolina 29745

Mitch H.

Job Details: 03/06/2025

"Checked and tested, found dryer operating properly. Customer has already replaced belt, idler, and guide wheels himself. Motor operating normally. No issues found. Collected for service call on cc"

We serviced a

WHIRLPOOL WASHER TL

Model WTW5057LW0

Near York, South Carolina 29745

Mitch H.

Job Details: 03/06/2025

"Checked and tested. Found wires to drain pump broken. Removed and replaced lower harness. Reassembled, tested, washer now operating properly.; used 1 W11643701 (Harness) from stock"

We serviced a

MAYTAG WASHER TOP LOAD

Model MVW6230HW1

Near Clover, South Carolina 29710

Mitch H.

Job Details: 03/06/2025

Checked and found washer will not power on or enter diagnostics. Has correct incoming power. Got lid open so customer could remove clothes. Ordering control and strike. Checked part availability and scheduled return for 3/12 PM ; ordrng 1 W11457841 (Strike) and 1 W11543994 (Control)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ09

Near Clover, South Carolina 29710

Mitch H.

Job Details: 03/06/2025

Removed and replaced LED module. All lights now operating properly.

We serviced a

WHIRLPOOL REFRIGERATOR BO

Model WRF767SDHZ01

Near Lake Wylie, South Carolina 29710

Mitch H.

Job Details: 03/06/2025

Checked and freezer ice maker broken where bail arm connects. Bail arm will not stay in place. Ordering ice maker. Checked part availability and scheduled return for 3/13 PM ; ordrng 1 W10886939 (Ice maker)

We serviced a

WHIRLPOOL REFRIGERATOR FDB

Model WRX735SDHZ08

Near Lancaster, South Carolina 29720

Jonathan J.

Job Details: 03/06/2025

Complaint unit not dispensing whole ice. I found solenoid for seized winding resistance was two ohms of resistance. Shorted winding I also found even after replacing solenoid solenoid would still not activate. I found that relay clicks on black wire yellow stripe to white wire is getting about 15 V AC current should be 120 V AC current at control board same voltage at harness attaching to icemaker. I found relay is bad I suspect. I advised customer could still be user interface as well. I am not 100% ruling it out yet.; ordrng 1 W11556912 (Control)

We serviced a

WHIRLPOOL REFRIGERATOR FDB

Model WRT518SZFM04

Near Lancaster, South Carolina 29720

Jonathan J.

Job Details: 03/06/2025

I replaced previously ordered parts tested operations. Unit is cooling after plugging unit in.

We serviced a

MAYTAG DRYER

Model MED5630HW2

Near Lancaster, South Carolina 29720

Jonathan J.

Job Details: 03/06/2025

Complaint seeing orange glowing from the back of the dryer inside of the dryer where the heat comes out complaining by an obnoxious odor. I found charcoal debris in burner box around heating element inspected burner no issues with the burner inspected all wiring no issues with wiring suspect debris. Had gotten down into burn box somehow. No safety issues found no wiring issues no control board issues. 7741041635 safety file number.

We serviced a

WHIRLPOOL WASHER TOP LOAD

Model WTW5105HW1

Near Wingate, North Carolina 28174

Jonathan J.

Job Details: 03/06/2025

"F0e3 f7e7 f7e1 f7e1 I replaced previously ordered parts cleared error codes found gear case is leaking oil heavily all over drive belt found customers water inlet hose on hot side is also leaking water and has been for quite some time has caused wall damage. We need gear case wash plate, agitator assembly, and associated parts. Agitator is seized in place tried removing could not remove will have to break agitator wash plate assembly with sledgehammer to access spanner nut.; ordrng 1 W11239857 (Belt) and 1 W10721967 (Cam) and 1 W11449840 (Gearcase) and 1 W11551646 (Nut) and 1 W11550891 (Agitator)"

We serviced a

WHIRLPOOL WASHER TOP LOAD

Model WTW5057LW0

Near Monroe, North Carolina 28112

Jonathan J.

Job Details: 03/06/2025

"Complaint washing machine just flashes will not wash will not start a cycle. Immediately powers itself off. I found error codes and cleared F9e1 f8e6 I found drain pump harness is broken at Y fork coming off of main harness. I spliced blue wire so customer could use it as a temporary repair. also found Kim was melted. Replaced cam.; ordrng 1 W11643701 (HARNESS LOWER), used 1 W10721967 (CAM KIT) from stock"

We serviced a

MAYTAG WASHER TOP LOAD

Model MVW6230HW0

Near Rock Hill, South Carolina 29732

Mitch H.

Job Details: 03/06/2025

"Removed and replaced control and actuator. Entered diagnostics. Ran DLMS calibration then diagnostics cycle. All completed properly. Tested washer, all components and functions operating correctly."

We serviced a

KITCHENAID DISHWASHER

Model KDTM405PPS1

Near Charlotte, North Carolina 28215

Johnny

Job Details: 03/06/2025

No error codes no leaks. Unit works as designed. Cx complaint was the gap between top of dishwasher and counter. Informed cx she will have to contact the builder of home to rectify her visual displeasure with the installation of the unit. No functional failures. Unit working as designed.

We serviced a

MAYTAG WASHER TOP LOAD

Model MVW7230HW1

Near Charlotte, North Carolina 28213

Johnny

Job Details: 03/06/2025

"Upon arrival cx was using unit with extra power button activated which would explain low water complaint. Noise complaint could not be duplicated. Checked error codes. Got f0e3 overload error along with f7e4 basket engagement error, cx stated nephew had too much laundry in washer. Based off information and error codes I conclude unit was overload causing basket to sit on the floor and preventing rotor from spinning. Cleared error codes, ran service cycle, no issues, unit working as designed."

We serviced a

MAYTAG REFRIGERATOR FDB

Model MFX2676FRZ00

Near Charlotte, North Carolina 28278

Clinton

Job Details: 03/06/2025

Installed ui tried to force a cycle in test mode after still didnt work. Checked ice maker connection were still in place unit is cold enough. Replaced ice maker again from truck stock I believe the previous tech truck stock may have been defective ; used 1 W11658802 (ICE MAKER) from stock

We serviced a

MAYTAG RANGE

Model MER6600FZ1

Near Grafton, Massachusetts 01536

Glenn

Job Details: 03/06/2025

Right rear element is open and right front switch is not providing voltage to the switch order parts ; ordrng 1 W11171119 (Right rear element) and 1 WP3149400 (Righ front switch)

We serviced a

WHIRLPOOL WASHER

Model WTW4850HW3

Near Charlotte, North Carolina 28277

Jonathan J.

Job Details: 03/06/2025

Replacement control tested operations no further issues found after performing a calibration procedure on the control.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ08

Near Fort Mill, South Carolina 29707

Jonathan J.

Job Details: 03/06/2025

Compressor was with another technician re-ordering compressor for tomorrow morning; ordrng 1 W11580057 (Compressor)

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730HAMZ0

Near Grafton, Massachusetts 01536

Glenn

Job Details: 03/06/2025

Complaint intermittent drip on the left side dripped 3 times. Tested no error codes present. Ran wash cycle no leaks at this time ran diagnostics test all tested ok NO leaks found customer instruction on proper loading etc

We serviced a

MAYTAG WASHER

Model MVWB835DW4

Near Millbury, Massachusetts 01527

Glenn

Job Details: 03/06/2025

Installed parts tested all ok

We serviced a

KITCHENAID DISHWASHER

Model KDFM404KPS0

Near Millbury, Massachusetts 01527

Glenn

Job Details: 03/06/2025

Installed lower door seal tested all ok

We serviced a

WHIRLPOOL WASHER TOP LOAD

Model WTW4855HW3

Near Indian Land, South Carolina 29707

Brandon

Job Details: 03/06/2025

On arrival I replaced control board using one that was sent with me. After installation unit tested as designed.No other issues found.

We serviced a

WHIRLPOOL MICROWAVE

Model GT4175SPS4

Near Waxhaw, North Carolina 28173

Brandon

Job Details: 03/06/2025

Complaint unit is not working. Found on arrival that unit is working intermittently. Found that door switches are bad. Ordering door switches and holder for repair.; ordrng 1 WP8185271 (Mount) and 3 4392027 (Switch)s

We serviced a

KITCHENAID M/W OTR

Model KMBS104ESS02

Near Waxhaw, North Carolina 28173

Brandon

Job Details: 03/06/2025

On arrival I replaced the control because display was the wrong color. Managed to fix problem with just control. All buttons and functions tested fine after installing control board. No other issues found

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS3

Near Waxhaw, North Carolina 28173

Brandon

Job Details: 03/06/2025

Complaint insulation is hanging out of door. On arrival I tucked insulation into door and tested unit. Unit tested as designed. No issues or leaks.

We serviced a

KITCHENAID DISHWASHER

Model KDTE234GPS0

Near Fort Mill, South Carolina 29707

Brandon

Job Details: 03/06/2025

Tested unit for 35 minutes and it did not leak. Ran multiple cycles on it and all components tested fine. Took bottom panel off and checked under unit. No leaks detected.Customer said that they would call back if it did.

We serviced a

MAYTAG DRYER

Model MEDB835DC4

Near Rock Hill, South Carolina 29730

Brandon

Job Details: 03/06/2025

Complaint dryer is not heating. Found dryer element was broken. Replaced using truck stock. Tested unit after installation and it tested functional. Heating and turning as designed. No other issues found.; used 1 WP3387747 (ELEMENT) from stock

We serviced a

SAMSUNG WASHER FL

Model WF45T6000AW

Near Cumberland, Rhode Island 02864

Lee

Job Details: 03/06/2025

"Customer states leaking from doorConfirmed issue, found bellow has torn, needs replacement ; ordrng 1 DC64-03788A (Bellow)"

We serviced a

WHIRLPOOL M/W OTR

Model WMH31017HS12

Near Charlotte, North Carolina 28262

Johnny

Job Details: 03/06/2025

"Noise complaint confirmed noise was coming from fan rubbing on exhaust vent flap when in use, bent flap back up away from. Tested unit. Noise no longer present. Unit working as designed."

We serviced a

GENERAL ELECTRIC RANGE

Model JBS360RM1SS

Near Brockton, Massachusetts 02302

Aimee

Job Details: 03/06/2025

No one speaks English at house . They speak PortugueseExplained the 2 burners arent covered. They would have to buy them.Husband will pick up at Lowes.Installed new Infi 2 switch front right and small Infi switch. With New recpticles complete

We serviced a

MAYTAG WASHER TL

Model MVWC465HW3

Near Brockton, Massachusetts 02301

Aimee

Job Details: 03/06/2025

"Cust didnt fix drain issue needs plumber, over flows drain and leaks over floor. I put bucket under.Installed parts and tested also leveled as much as could. Cust bought new hose and I installed for them.Tested with towels and spunWet cardboard over basement almost fell through wall.Explained to customer multi times need to shovel dirt off cement floor and level washer and take care of drain Tossing layer of card board on floor isnt leveling . Also need to run a dehumidifier washer rusting at bottom; dspstn on spec-tagged invntry: 1 W10721967 CAM KIT and 1 W10913953 ACTUATOR"

We serviced a

MAYTAG WASHER TL

Model MVW5430MW0

Near Medway, Massachusetts 02053

Aimee

Job Details: 03/06/2025

"Had to break latch to get model number Found break in harness and needs drain pump, control, latch; rqstng P&A on 1 W11643701 (Harness) and 1 W11670519 (Latch) and 1 W11627413 (Control), dspstn on spec-tagged invntry: 1 W11399437 DRAIN PUMP"

We serviced a

WHIRLPOOL REFRIGERATOR FDB

Model WRX986SIHZ01

Near Franklin, Massachusetts 02038

Aimee

Job Details: 03/06/2025

Found the freezer fan buzzing and needs new right gasket.; rqstng P&A on 1 W10846057 (Gasket) and 1 W11032800 (Freezer fan)

We serviced a

WHIRLPOOL WASHER TL

Model WTW8127LW1

Near Monson, Massachusetts 01057

Chris B.

Job Details: 03/06/2025

Complaint that the washer is making a grinding noise when in use. Found error codes F6E3. Found heavy grinding and knocking noises. Found rotor screw came off affecting the motors and gear case. Will order all parts for a return visit.; ordrng 1 W11449841 (Gear Case) and 1 W10734521 (Clutch) and 1 W11260238 (Rotor) and 1 W11195971 (Stator) and 1 W10754448 (Clutch) and 1 W11510461 (Wash Plate) and 1 W11551646 (Nut) and 1 W10752187 (Screw) and 1 W10752189 (Screw) and 1 2xFrameJob (2x Frame Job)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ05

Near Springfield, Massachusetts 01119

Chris B.

Job Details: 03/06/2025

Complaint that the ice maker is releasing more pieces of plastic. Found broken bin causing pieces of plastic falling out to the cup when called for ice. Customer mentioned that they have been throwing away lots of pieces and the last few they save it from a few days back for evidence that is still an ongoing issue. Will order part for a return visit.; ordrng 1 WPW10558423 (Ice Bucket)

We serviced a

LG DISHWASHER

Model LSDTS9882S

Near Springfield, Massachusetts 01119

Chris B.

Job Details: 03/06/2025

Complaint that is still not washing the dishes properly. Found two issues. One is that the heating element is not turning on after multiple attempts. Got 12 ohms on the element but only 8v on the harness. Two the unit has washing pressure but not enough to fill the top rack. Will put in for a new control board and pump/ heater assembly.; rqstng P&A on 1 AGM76429513 (Control Board)

We serviced a

MAYTAG WASHER TL

Model MVWC565FW3

Near Somers, Connecticut 06071

Jorden

Job Details: 03/06/2025

"Arrived and found error code F7E4 (shifter fault) stored in system, cleared code. Ran auto test cycles and calibration cycle, unit tests fine on all accounts. Customer education on how to properly utilize cycles and options and how to cancel a cycle not just pause. (Found customer had started pressing the button twice to get it started effectively pausing every cycle right at the start). Informed customer should we return and find no manufacturing defect then customer would be responsible for service fee."

We serviced a

SAMSUNG DRYER

Model DVE45R6300V/A3

Near Franklin, Massachusetts 02038

Aimee

Job Details: 03/06/2025

"Installed tune up kit , fuse and heater completeChanged hose for customer husband will need to replace out side vent fell off in wind .Which causing water in vent hose.I connected the back dryer Cust buying new flap and needs to connect other side the vent at house .I explained to wife ; dspstn on spec-tagged invntry: 1 DESAMKIT DRYER REPAIR KIT"

We serviced a

JENN-AIR REFRIGERATOR

Model JFC2087HRS

Near Shrewsbury, Massachusetts 01545

Glenn

Job Details: 03/06/2025

Installed valve tested no dripping all ok no leaks took pics

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ07

Near Rock Hill, South Carolina 29732

Mitch H.

Job Details: 03/06/2025

Removed and replaced both RC door gaskets. Used heat gun to form gaskets and ensured proper seal around full perimeter of doors. All operating properly.

We serviced a

WHIRLPOOL REFRIGERATOR SXS

Model WRS571CIHZ01

Near Westfield, Massachusetts 01085

Mike K.

Job Details: 03/06/2025

"Replaced females replaced last visit, hasnt worked since. Found broken lines in door harness, ordering door. Advised cs that door would ship direct to her, to open box and ensure not damaged, then contact us to schedule return to install.; ordrng 1 LW11202405 (Fr door assy)"

We serviced a

GE REFRIGERATOR FDB

Model GFE28GYNHFS

Near Southwick, Massachusetts 01077

Mike K.

Job Details: 03/06/2025

"Unit not cooling properly after repair, rf is 46, 33 in fr.Unit was on turbo cool for both sections. Set to normal cooling, 10 minutes later found both hot vap fans running. Verified with ge techline that the system will run both at same time. Gave history and he suggested pulling into vacuum and recharging.Pulled into vacuum, charged with nitrogen at 200psi, bubbles tested all joints made, all test fine. Pulled into vacuum again, held from me for 5+ minutes. Preheated new can of f refrigerant and overfilled per techline suggestion. Filled with 68 grams of r600aWith failure to go into diagnostics properly before, will order control and have cs monitor in the mean time.Office to contact when parts come in to schedule return.; rqstng P&A on 1 WR55X46805 (Control) and 1 WR55X44126 (Control (top of left rf door)), ordrng 1 WR86X10094 (3 wat valve assy)"

We serviced a

MAYTAG WASHER TL

Model WTW5105HW0

Near Southington, Connecticut 06489

Andre

Job Details: 03/06/2025

Ck unit upon arrival and remove and install control with harness and calibrate unit and ran cycle unit operating to normal specs. Customer will not ran regular cycle and monitor unit

We serviced a

MAYTAG WASHER TOP LOAD

Model MVWC400XW3

Near Meriden, Connecticut 06451

Andre

Job Details: 03/06/2025

F7E6Ck unit upon arrival and found F7E6 error code. Rand all agitation and spin cycle on unit and all operation test passes. Ran quick wash and unit complete quick wash test. Ran calibration and inform customer of findings and what was done. unable to find any specific faulty at this time

We serviced a

MAYTAG WASHER

Model MVW6230HC0

Near Chicopee, Massachusetts 01020

Chris B.

Job Details: 03/06/2025

Complaint that the washer is not starting any cycle. F5E4 ran diagnostic and calibration cycle. Found unit unbalanced. Adjusted balance and ran a normal cycle with clothes and all working normal.

We serviced a

WHIRLPOOL WASHER

Model WTW5015LW0

Near Middletown, Connecticut 06457

Andre

Job Details: 03/06/2025

Ck unit upon arrival and found F9E1 error code with help from maintenance worker drain as much water out of unit and tilt unit and found harness Tape up with electrical tap when I went under. Remove and add Red Butt connector for temporary fix that customer can able to use harness and order harness for; ordrng 1 W11643701 (Harness)

We serviced a

WHIRLPOOL RANGE

Model WFES3030RS0

Near Middletown, Connecticut 06457

Andre

Job Details: 03/06/2025

Ck unit upon arrival and remove defective rubber gasket and install newly design door gasket unit now operating to manufacturers specs

We serviced a

MAYTAG WASHER TOP LOAD

Model MVWC400XW3

Near Meriden, Connecticut 06451

Andre

Job Details: 03/06/2025

Contact Us Today

About Us